imx6 mac地址设置

imx6的mac地址总是固定的值，所以需要更改，采用的方法是在uboot中设置环境变量,之后在kernel中使用uboot中设置的mac地址的值。本文记录更改的过程。

参考链接：

　　http://www.cnblogs.com/zengjfgit/p/5711304.html

uboot

lib_arm/board.c void start_armboot (void) { ...eth_initialize(gd->bd); ---------------------------+... | }; | | | int eth_initialize(bd_t *bis) <-------------+ { ....../* Try board-specific initialization first. If it fails or isn't * present, try the cpu-specific initialization */ if (board_eth_init(bis) < 0) cpu_eth_init(bis); -------------+ ...... | } | | int cpu_eth_init(bd_t *bis) <--------+ { int rc = -ENODEV; #if defined(CONFIG_MXC_FEC) rc = mxc_fec_initialize(bis); ------+ | /* Board level init */ | enet_board_init(); | | #endif | return rc; | } | | int mxc_fec_initialize(bd_t *bis) <------+ { ......if (fec_get_hwaddr(dev, ethaddr) == 0) { ------+ printf("got MAC address from IIM: %pM\n", ethaddr); | memcpy(dev->enetaddr, ethaddr, 6); | fec_set_hwaddr(dev); | } | } | | return 1; | } | | static int fec_get_hwaddr(struct eth_device *dev, unsigned char *mac)<--+ { #ifdef CONFIG_GET_FEC_MAC_ADDR_FROM_IIM fec_get_mac_addr(mac); -------+ return 0; | #else | return -1; | #endif | } | | #ifdef CONFIG_GET_FEC_MAC_ADDR_FROM_IIM | int fec_get_mac_addr(unsigned char *mac) <---- + { #if 0 unsigned int value; //不读取寄存器中的值 value = readl(OCOTP_BASE_ADDR + HW_OCOTP_MACn(0)); mac[5] = value & 0xff; mac[4] = (value >> 8) & 0xff; mac[3] = (value >> 16) & 0xff; mac[2] = (value >> 24) & 0xff; value = readl(OCOTP_BASE_ADDR + HW_OCOTP_MACn(1)); mac[1] = value & 0xff; mac[0] = (value >> 8) & 0xff; #else eth_getenv_enetaddr("ethaddr", mac); //使用环境变量设置的mac地址 #endif return 0; }

kernel

1.设备

arch/arm/mach-mx6/board-mx6q_sabresd.c MACHINE_START(MX6Q_SABRESD, "Freescale i.MX 6Quad/DualLite/Solo Sabre-SD Board")/* Maintainer: Freescale Semiconductor, Inc. */.boot_params = MX6_PHYS_OFFSET + 0x100,.fixup = fixup_mxc_board,.map_io = mx6_map_io,.init_irq = mx6_init_irq,.init_machine = mx6_sabresd_board_init,.timer = &mx6_sabresd_timer,.reserve = mx6q_sabresd_reserve, MACHINE_ENDstatic void __init mx6_sabresd_board_init(void) {......imx6_init_fec(fec_data);...... }arch/arm/mach-mx6/mx6_fec.c void __init imx6_init_fec(struct fec_platform_data fec_data) {//读取寄存器中的mac地址的值fec_get_mac_addr(fec_data.mac);//这里就已经随机生成了mac地址，在驱动中就不会再次设置，所以注释了//设备注册在驱动注册之前，先不要自动生成mac地址，由驱动来设置 // if (!is_valid_ether_addr(fec_data.mac)) // random_ether_addr(fec_data.mac);if (cpu_is_mx6sl())imx6sl_add_fec(&fec_data);elseimx6q_add_fec(&fec_data); }

2.驱动

drivers/net/fec.c //驱动设置mac地址 static void __inline__ fec_get_mac(struct net_device *ndev) {struct fec_enet_private *fep = netdev_priv(ndev);struct fec_platform_data *pdata = fep->pdev->dev.platform_data;unsigned char *iap, tmpaddr[ETH_ALEN];/** try to get mac address in following order:** 1) module parameter via kernel command line in form* fec.macaddr=0x00,0x04,0x9f,0x01,0x30,0xe0*/iap = macaddr;// 检查是否合法，不合法就通过flash设置/** 2) from flash or fuse (via platform data)*/if (!is_valid_ether_addr(iap)) { #ifdef CONFIG_M5272if (FEC_FLASHMAC)iap = (unsigned char *)FEC_FLASHMAC; #elseif (pdata)memcpy(iap, pdata->mac, ETH_ALEN); #endif}// 检查是否合法，不合法就通过bootloader设置/** 3) FEC mac registers set by bootloader*/if (!is_valid_ether_addr(iap)) {*((unsigned long *) &tmpaddr[0]) =be32_to_cpu(readl(fep->hwp + FEC_ADDR_LOW));*((unsigned short *) &tmpaddr[4]) =be16_to_cpu(readl(fep->hwp + FEC_ADDR_HIGH) >> 16);iap = &tmpaddr[0];}// 随机生成/** 4) generate random mac */if (!is_valid_ether_addr(iap)) random_ether_addr(iap);memcpy(ndev->dev_addr, iap, ETH_ALEN);/* Adjust MAC if using macaddr */if (iap == macaddr)ndev->dev_addr[ETH_ALEN-1] = macaddr[ETH_ALEN-1] + fep->pdev->id; }

Tony Liu

2016-9-22, Shenzhen

转载于:https://www.cnblogs.com/helloworldtoyou/p/5895778.html

总结

以上是生活随笔为你收集整理的imx6 mac地址设置的全部内容，希望文章能够帮你解决所遇到的问题。

如果觉得生活随笔网站内容还不错，欢迎将生活随笔推荐给好友。